General Hardware Input/output
Autos, Relays &
OSI 3 - Network layer
TCP/IP (aka "The Internet"),
Packet Radio, EDI,
Telephone / pagers
Logic Levels, Digital
to Analog, Analog to Digital,
DSP, Modem signals,
/techref/pcbixmax.htm Maximum interconnect options from
minimum board space+
DesignGroupLa of DAC
Modem features like AT command set, DTMF decode and Caller ID Ring detect
and audio I/O for PIC
http://www.learn-c.com/ Control And
Embedded Systems. Tutorials and a Low cost PC IO board design.
Peacock's superb guide to all things serial and parallel.
has info on various ports (parallel, serial, keyboard, etc.)
The comp.sys.ibm.pc.hardware.* FAQ (posted on news.answers and
comp.sys.ibm.pc.hardware.misc, available via ftp from
contains connector/bus pinouts and other useful information.
IBM, Technical Reference, Personal Computer AT, 1984
"The IBM Personal Computer, from the Inside Out" by Sargent and Shoemaker
(published by Addison-Wesley) provides a lot of information about interfacing
an IBM type PC to various things.
Talking to a floppy control from NC4000:
Using a non-DOS machine to talk to a DOS disk
www.national.com Look up the datasheets
for their super-IO parts, which have Paralell Port, Serial Port, RTC, Floppy
Controller, all in one chip.
16- and 32-bit DLLs for port I/O may be found at:
WINio.Dll and WIN32io for Windows 95
Accessing PC I/O ports in Windows
EDE300 Application Note #1: Device Control via the PC
http://www.elabinc.com In the 'Integrated
Circuits' section under 'EDE300'
The Analog Devices AD9850 is a CMOS, 125 MHz complete direct digital synthesiser
on a single chip. It uses a single 5 V or 3.3 V supply, and with a 125 MHz
clock, can generate a low-distortion sine wave or a square wave, from under
1 Hz up to about 60 MHz, with a tuning resolution of 0.0291 Hz. Full data
on the device is available from ADI's web site: http://www.analog.com
Commercial Communication Standards
from the Defense Information Systems Agency
- audio recording info.
"low-cost interface boards" to plug into a PC (ISA, PCI, serial, parallel,
USB, FireWire, ...)
analog input/output: see io/atod.htm
spamdude2zspam at yahoo.com
I'm trying to build be a cnc machine controlled with a PC computer.
Has anybody used the X100 PC ISA I/O board from Tecel?
I would like to know how reliable is it.
$40.00 : the X100 PC ISA I/O board from Tecel
Maximum interconnect options from minimum board space
| ||©2018 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?|
<A HREF="http://www.piclist.com/techref/ios.htm?key=output"> I/O Port,Input Port,Output Port,Input/Output</A>
PICList 2018 contributors:
List host: MIT,
Site host massmind.org,
Top posters @20181113 RussellMc, Van Horn, David, Sean Breheny, David C Brown, Isaac M. Bavaresco, Neil, Bob Blick, John Gardner, AB Pearce - UKRI STFC, Harold Hallikainen,
* Page Editors:
Roman Black of Black Robotics
donates from sales of
stepper controller kits.
* Ashley Roll of Digital Nemesis
donates from sales of
RCL-1 RS232 to
* Monthly Subscribers:
on-going support is MOST appreciated!
Richard Seriani, Sr.
Welcome to www.piclist.com!