please dont rip this site

Language Pcl LJ2078

USING  THE CHARACTER SLANT ( SL ) COMMAND

     
     The Character Slant command ( SL ) specifies the slant
     at which labels are drawn.  For more information see
     the Updated PCL 5 Printer Language Technical Reference
     Manual. The syntax for the command is as follows:
     
     SL tangent of angle; or SL;
     
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT.
     
     
     EcE                           Resets the printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes HP-GL/2 mode.
     
     SP1;                          Selects pen number 1,
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     SD1,21,2,1,4,25,5,0,6,0,7,4101;    Designates a 25
                                   point CG times font as
                                   the standard (primary)
                                   font.
     
     SI.7,1;PA1000,1000;           Sets the absolute
                                   character size to .7 cm
                                   wide by 1 cm high; moves
                                   to (1000,1000).
     
     DT#,1;                        Defines the label
                                   terminator as the "#"
                                   character, and the 1
                                   designates it as non-
                                   printing.
     
     SL.36;LBSlant#;               Sets the slant angle for
                                   20 degrees from the
                                   vertical (forward slant),
                                   and prints "Slant."
     
     PA1000,300;SL-.36;LBSlant#;   Moves to (1000,300);
                                   changes the slant angle
                                   to -20 degrees from
                                   upright and prints
                                   "Slant".
     
     Ec%0A                         Enters PCL mode.
     
     EcE                           Sends a reset to end the
                                   job and eject the page.


            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.




file: /Techref/language/pcl/lj2078.asc, 2KB, , updated: 1993/11/15 17:26, local time: 2017/10/23 17:57,
TOP NEW HELP FIND: 
54.224.50.28:LOG IN

 ©2017 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE! / 

<A HREF="http://www.piclist.com/techref/language/pcl/lj2078.asc"> language pcl lj2078</A>

Did you find what you needed?

  PICList 2017 contributors:
o List host: MIT, Site host massmind.org, Top posters @20171023 RussellMc, Van Horn, David, James Cameron, Sean Breheny, IVP, alan.b.pearce, Neil, David C Brown, Bob Blick, Denny Esterline,
* Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .