please dont rip this site

Language Pcl LJ1877

FILLING WEDGES AND CIRCLES

    
     The wedge commands, Edge Wedge (EW) and Fill Wedge
     (WG), use your current pen location as the center point
     of the wedge. You then specify the radius, the start
     angle, and the sweep angle to complete the wedge. The
     angles are measured counterclockwise, with zero at the
     3 o-clock position.  For more information see the PCL 5
     Printer Language Technical Reference Manual.
     
     Syntax for the Edge Wedge command is: EW[radius],[start
     angle],[sweep angle];
     
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT.
     
     
     EcE                           Resets the printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes Hp-GL/2 mode.
     
     SP1;                          Selects pen number 1,
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     PA1400,2500;                  Selects absolute plotting
                                   mode and moves the pen to
                                   (1400,2500).
     
     WG600,150,120;                Fills a wedge with radius
                                   600 plotter units (plu),
                                   start angle 150 degrees,
                                   and sweep angle 120
                                   degrees. Since no fill
                                   type was specified, the
                                   wedge is black (solid
                                   black is the default fill
                                   type).
     
     PA2300,2500;FT3,75,45;        Specifies absolute
                                   plotting and moves to
                                   (2300,2500). Selects the
                                   fill type to be number 3
                                   (hatching-parallel
                                   lines), with 75 plu
                                   between hatching lines,
                                   and hatching lines tilted
                                   at 45 degree angles.
     
     WG600,90,180;                 Fills a wedge with the
                                   current fill type, using
                                   a radius 600 plu, a start
                                   angle 90 degrees, and a
                                   sweep 180 degrees.
     
     FT1,0,0;WG600,270,60;         Specifies a fill type of
                                   solid black and fills a
                                   wedge using the same
                                   center and radius as the
                                   previous wedge, but
                                   starts this wedge at 270
                                   degrees with a sweep of
                                   60 degrees.
     
     FT4,60,45;WG600,330,120;      Specifies a fill type of
                                   number 4, (cross-
                                   hatching) with 60 plu
                                   between lines and the
                                   lines tilted at 45
                                   degrees. Fills a wedge
                                   using the same center and
                                   radius as the previous
                                   two wedges, but starts
                                   this wedge at 330 degrees
                                   with a sweep of 120
                                   degrees.
     
     PA3500,2500;WG400,0,360;      Selects a new absolute
                                   plotting point and moves
                                   to it, (3500,2500)
                                   Creates a filled circle
                                   using the current fill
                                   type of number 4 (cross-
                                   hatching), and specifies
                                   a start angle 0 degrees
                                   with a 360 degree sweep.
     
     PA4500,2500;FT;WG400,0,360;   Moves to (4500,2500) and
                                   begins absolute plotting.
                                   Selects a solid black
                                   fill to fill a wedge with
                                   a 400 plu radius, and
                                   sweep of 360 degrees, (a
                                   circle).
     
     Ec%0A                         Enters the PCL mode.
     
     EcE                           Sends a reset to end the
                                   job and eject the page.
     
     
            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.
     


file: /Techref/language/pcl/lj1877.asc, 5KB, , updated: 1993/11/15 17:11, local time: 2017/10/21 18:30,
TOP NEW HELP FIND: 
54.80.137.168:LOG IN

 ©2017 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE! / 

<A HREF="http://www.piclist.com/techref/language/pcl/lj1877.asc"> language pcl lj1877</A>

Did you find what you needed?

  PICList 2017 contributors:
o List host: MIT, Site host massmind.org, Top posters @20171021 RussellMc, Van Horn, David, James Cameron, Sean Breheny, IVP, alan.b.pearce, Neil, David C Brown, Bob Blick, Denny Esterline,
* Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .