please dont rip this site

RS-485, RS485


See also:

See also:

Simon Nield at QUANTEL.COM says:

{the above} assumes you are using 2 wire rs485, which gives one datapath & is therefor half-duplex. 4 wire rs485 gives 2 datapaths and can be full duplex.

{...} if you are designing a new system then you may well want to think about 4 wire 485, it'll can be a lot more like 232 from a software point of view, which can make things a lot easier - also means your slaves don't have to spend time listening to each others packets, which can give you a nice code boost. (you use one pair from master to slaves and one pair from slaves to master - so each link is unidirectional). cat5 may be a good choice for cabling; you have plenty of twisted pairs, it's cheap, and its often in the walls already. if you do use cat5 then do check the pairing of the wires as they are a little odd. if you can limit the baud rate then using slew rate limited drivers will make emissions testing a lot easier.

One final point in favour of 4 wire 485 - trying to change direction with the serial ports on a pc with windows is slow as slow can be (assuming you are using an rts controlled converter) as in 20ms or so dead time. this makes polling multiple units a good way to waste loads of bandwidth. one solution if you really do want 2 wire is to use a decent rs485 PCI card. the ones I have tried (from oxford semi) were loads faster at turn around in half duplex (practically instantaneous turnaround at 115200)..... could be that this is due to better optimised drivers for the oxsemi board, or it could be hardware.


file: /Techref/io/serial/rs485s.htm, 3KB, , updated: 2013/2/1 18:35, local time: 2014/7/28 01:49, owner: jap-almos-,
TOP NEW HELP FIND: 
54.197.19.35:LOG IN

 ©2014 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE! / 

<A HREF="http://www.piclist.com/techref/io/serial/rs485s.htm"> RS-485, RS485</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

  PICList 2014 contributors:
o List host: MIT, Site host massmind.org, Top posters @20140728 RussellMc, Richard R. Pope, IVP, John Gardner, alan.b.pearce, James Cameron, Isaac Marino Bavaresco, Bob Blick, Josh Koffman, David C Brown,
* Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .