please dont rip this site

Infra-Red Input / Output

LED's pulsed for say 200% of their 'normal' current at a 50% duty cycle appear brighter than 100% current for 100% duty cycle even though the maths says that it's all the same average current. Remote controls are almost always pulsed. In fact, if you want to get more than a couple of feet covered, you almost *have* to pulse the IR LEDs. Note that since current in a series circuit is the same through all the series elements (non-reactive), you can string several LEDs in series and pulse the whole string using the same amount of total energy that you would have used to pulse just one. Instead of wasting the energy as heat in a resistor, you recover it as more usefil light from the LEDs. Multiple LEDs give you better 'coverage' than a single LED.

VCSEL laser diodes in plastic LED type packages collimated to 2 degrees beamwidth are simple to drive (constant current, no monitor diode needed), and best of all--VCSEL laser diodes begin lasing at 4 ma. IR beams can be 'hidden' on the tx and rx ends of the link by dark plastic (as your VCR has on it's front panel)-when you scrap a junk vcr, ALWAYS SAVE the black plastic in front of the IR recveiver module, same with some hand held remote control transmitters. VCSEL laser diodes are ideal for moderate range free space laser comm ap because the drivers are simple!

Microchip PIC specific IR I/O

Ubicom SX specific IR I/O

irda

IR Remotes@ LEDs@, Light Sensors@

See also:

IR standards?

Archive:


file: /Techref/io/irs.htm, 4KB, , updated: 2013/7/22 16:38, local time: 2017/12/17 19:54,
TOP NEW HELP FIND: 
54.91.171.137:LOG IN

 ©2017 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE! / 

<A HREF="http://www.piclist.com/techref/io/irs.htm?key=irda"> IRDA, 890nm, 940nm, Infra-Red Input / Output</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed? "irda"

  PICList 2017 contributors:
o List host: MIT, Site host massmind.org, Top posters @20171217 RussellMc, Van Horn, David, Sean Breheny, James Cameron, alan.b.pearce, IVP, Neil, Bob Blick, David C Brown, John Gardner,
* Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .