please dont rip this site

Language Pcl LJ2006.ASC

USING  THE FILL TYPE COMMAND

     
     This command selects the shading pattern used to fill
     polygons ( FP ), rectangles ( RA or RR ), wedges ( WG
     ), or characters ( CF ). The Fill Type command ( FT ),
     can use solid, shading, parallel lines (hatching),
     cross hatching, patterned (raster) fill, or PCL user-
     defined patterns. For more information see the PCL 5
     Printer Language Technical Reference Manual. The syntax
     for this command is as follows:
     
     FT fill type,[option1,[option2]]; or FT;
     
     
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT.
     
     
     
     
     EcE                           Resets the printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes HP-GL/2 mode.
     
     SP1;                          Selects pen number 1,
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     PA2000,2000;                  Specifies absolute
                                   plotting and moves to
                                   location (2000,2000).
     
     FT;RR2500,300;ER2500,300;     Selects the default fill
                                   type (solid black); fills
                                   a rectangle using solid
                                   black fill, with the
                                   lower left corner being
                                   the current pen location
                                   and the upper right
                                   corner a point 2500
                                   plotter units (plu) to
                                   the right and 300 plu up.
                                   Edges the rectangle just
                                   filled.
     
     PR0,300;FT3,80,30;RR2500,300; Specifies relative
                                   plotting and moves the
                                   pen up 300 plu; selects
                                   fill type number 3
                                   (parallel lines), with 80
                                   plu between each line,
                                   with each line tipped 30
                                   degrees. The RR command
                                   fills the rectangle with
                                   the fill type just
                                   specified, using the
                                   current pen location as
                                   the lower left corner,
                                   and a point 2500 X-units
                                   and 300 Y-units away as
                                   the upper right corner.
     
     PR0,300;FT10,36;RR2500,300
     ER2500,300;                   Moves the pen position up
                                   300 plu and specifies the
                                   fill type as 36% shading;
                                   fills a rectangle with
                                   that fill type, with the
                                   lower left corner being
                                   the current pen location
                                   and the upper right
                                   corner 2500 plu to the
                                   right and 300 plu up from
                                   there. The ER command
                                   edges the rectangle just
                                   filled.
     
     Ec%0A                         Enters the PCL mode.
     
     EcE                           Sends a reset to end the
                                   job and eject the page.




            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.




file: /Techref/language/pcl/lj2006.asc, 4KB, , updated: 1993/11/15 17:20, local time: 2024/10/7 22:29,
TOP NEW HELP FIND: 
98.80.143.34:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.piclist.com/Techref/language/pcl/lj2006.asc"> language pcl lj2006</A>

Did you find what you needed?

  PICList 2024 contributors:
o List host: MIT, Site host massmind.org, Top posters @none found
- Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .