please dont rip this site

Language Pcl LJ1881.ASC

USING  ARC RELATIVE TO DRAW ARCS

    
     For more information see the PCL 5 Printer Language
     Technical Reference Manual.
     
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT
     
     EcE                           Resets the Printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes HP-GL/2 mode.
     
     SP1;                          Selects pen number 1
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     PA1500,1500;PD;               Specifies the starting
                                   position as (1500,1500)
                                   and puts the pen down.
     
     AR0,2000,80,25;               Draws an arc with a
                                   center point 0 Plotter
                                   Units (PLU) in the X
                                   direction and 2000 PLU in
                                   the Y direction from
                                   (1500,1500). Then it
                                   specifies an arc section
                                   to be 80 degrees
                                   (positive angle), with a
                                   chord angle of 25
                                   degrees.
     
     AR2000,0,80;                  Draws an arc with a
                                   center point 2000 PLU in
                                   the X direction and 0 PLU
                                   in the Y direction from
                                   the current pen position.
                                   Then specifies the arc
                                   section to be 80 degrees
                                   (positive angle), with a
                                   default chord angle of 5
                                   degrees.
     
     Ec%0A                         Enters PCL mode.
     
     EcE                           Send a reset to end the
                                   job and eject the page.
     
     
     
            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.
     


file: /Techref/language/pcl/lj1881.asc, 2KB, , updated: 1993/11/15 17:13, local time: 2024/10/7 23:55,
TOP NEW HELP FIND: 
98.80.143.34:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.piclist.com/Techref/language/pcl/lj1881.asc"> language pcl lj1881</A>

Did you find what you needed?

  PICList 2024 contributors:
o List host: MIT, Site host massmind.org, Top posters @none found
- Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to www.piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .