Searching \ for 'Open Drain Pullup' in subject line. ()
Make payments with PayPal - it's fast, free and secure! Help us get a faster server
FAQ page: www.piclist.com/techref/index.htm?key=open+drain+pullup
Search entire site for: 'Open Drain Pullup'.

Truncated match.
PICList Thread
'Open Drain Pullup'
1999\07\05@022601 by Stewart Pye

flavicon
face
Hi....

I'm interfacing a 16F84 to a 4051 analog mux with a 12V supply.
Is it safe to put a 10k pullup resistor to +12V from the open drain output
RA4?.


Thanks
Stewart.

1999\07\05@024054 by Jim Robertson

flavicon
face
At 23:30 4/07/99 -0700, you wrote:
>RA.4 can be pulled as high as 14V IIRC on the F84 part, should be fine,
>so long as your 12V supply doesn't spike or anything <G>
>
>  Mark

I am not saying Mark is right or wrong here but I would ask for a second
opinion before doing something as drastic as this. I just had a quick
look at the specs to confirm my suspicion and I did not see anything off hand
that would suggest you can do this. IIRC only the 17Cxx parts have high
voltage
pins (and some new 16C5x family member in the future parts list.)

Jim

{Quote hidden}

________________________________________
Email: spam_OUTnewfoundTakeThisOuTspampipeline.com.au
http://www.new-elect.com
WARP-13 SALE now on. $48USD with world delivery.
MPLAB compatible PIC programmers and firmware
upgrades for many programmers.
________________________________________

1999\07\05@024639 by Stewart Pye

flavicon
face
All I could see in the data sheet said maximum 6V on all I/O pins too.
What's the point of having an open drain output then?

Stewart.


{Quote hidden}

1999\07\05@030133 by Peter McAlpine

flavicon
face
Hi Stewart,
Could always use a series resistor and a zener
diode to ground or a normal diode to a 5v rail..

Regards
Peter Mcalpine
petermcaspamKILLspamozemail.com.au - http://www.ozemail.com.au/~petermca
.....mcalpineKILLspamspam.....gme.net.au - http://www.gme.net.au
http://www.wrx.org.au


{Original Message removed}

1999\07\05@032251 by Stewart Pye

flavicon
face
Say I used a diode going to 5v, wouldn't this bring the RA4 output down to
about 5.6v. Where would I take the address line from? I need about 10v to
go to the 4051. Anyway, I think I might use an open collector buffer. (i
have three other outputs going to the 4051. I was going to use transistors
for them.) I'll have to glue the buffer to the board as I've run out of space!

Thanks,
Stewart

At 05:01 PM 5/07/99 +1000, you wrote:
{Quote hidden}

>{Original Message removed}

1999\07\05@040038 by Mark Willis

flavicon
face
You could be right, Jim.  I think I am  & the datasheets are still not
up to date - the latest datasheets still say "Preliminary" i.e. file
DS30430C.PDF, it says nothing about an upper limit for the open-drain
pins (Parameter D150) - ALL the other parts I've been using (`C66 etc.)
have all been 14V limited on pin RA4, and on /MClr as well.  Not a good
idea to PUSH such limits, of course.  Would someone at Microchip PLEASE
Update Those Data Sheets - and add this specific item, which has been
debated here before?  (The F84 sheets could stand to not say
"Preliminary" any more, at least!  <G>)

Some support for my position here:
>From the PICList Archive, seems it's missing from the F84 data sheets
<G>
=====
Message Date: Thu Jan 1 14:29:50 1998
Author: John Payson

> But during programming MCLR is held at the programming voltage,
> so at least for that pin >VDD is allowed.
>
> So my question is: what voltage can be put on RA4?

According to a rep at Microchip, the max voltage on RA4 for the 16F84
etc.
is 14V independent of VDD.
=====
Message Date: Thu, 17 Apr 1997 08:52:47 -0700
Author: Brian Boles


It's in all of the newer ('96-97 or greater) data sheets. It was left
off of the old ones inadvertantly and is still not in the 16F84 or
16C84 data sheet.

However, the picture of the RA4 pin in the data sheet has always
correctly shown only a N-channel tr. on the pin in all data sheets.
Note that this feature is on the 16C55X/6X/6XX/7X/7XX/8X/9XX but not
on the 16C5X.

As Dr. Strangelove said, "But the whole point is lost if you don't
tell the world!"

Rgds, Brian.
=====

 Mark

Jim Robertson wrote:
{Quote hidden}

1999\07\06@090324 by Robert K. Johnson

flavicon
face
       Probable the results would be rather catastrophic, There is a 200µa li
mit
in current injected into any pin. If for ANY reason the protection diodes
are forward biased the chip will go into melt down. This comdition has been
known to burn labels off of 'JW' parts... One of the sure ways to destruct
a chip.

               Robert K. Johnson
               @spam@rkj1KILLspamspamix.netcom.com

At 04:30 PM 7/5/99 +1000, you wrote:
>Hi....
>
>I'm interfacing a 16F84 to a 4051 analog mux with a 12V supply.
>Is it safe to put a 10k pullup resistor to +12V from the open drain output
>RA4?.
>
>
>Thanks
>Stewart.

1999\07\06@114625 by Sean Breheny

face picon face
Hi Robert,

I don't think there are any protection diodes (or at least, none to Vdd) on
RA4, just because of this. In addition, there is no way the chip could go
into melt down through a 10K resistor.

Sean

At 10:02 PM 7/5/99 -0700, you wrote:
>        Probable the results would be rather catastrophic, There is a
200µa limit
{Quote hidden}

| Sean Breheny                  
| Amateur Radio Callsign: KA3YXM
| Electrical Engineering Student  
\--------------=----------------
Save lives, please look at http://www.all.org
Personal page: http://www.people.cornell.edu/pages/shb7
RemoveMEshb7TakeThisOuTspamcornell.edu ICQ #: 3329174
________________________________________________________
NetZero - We believe in a FREE Internet.  Shouldn't you?
Get your FREE Internet Access and Email at
http://www.netzero.net/download/index.html

1999\07\06@152322 by Mark Willis

flavicon
face
Read the .PDF file; no protection diodes to Vdd on /MClr or RA4,
definitely.

I'll ask my favorite FAE, though I'm pretty certain.

 Mark

Sean Breheny wrote:
{Quote hidden}

More... (looser matching)
- Last day of these posts
- In 1999 , 2000 only
- Today
- New search...